An oven that won't heat, bakes unevenly, stays locked after self-clean or shows an error code? Our local technicians repair gas and electric wall ovens and ranges across Leander.
These are the oven problems we get called about most. Open a question to see the usual causes and what you can safely check before you call.
In a gas oven the igniter has to glow hot enough to open the gas valve. A weak one takes far longer, or the burner lights and then goes out.
In an electric oven, a bake element with a damaged section heats slowly or only in part. Sometimes you can see a blister or a break on it.
The sensor tells the control how hot the oven is. When its reading drifts, the oven heats too slowly or stops short of the set temperature.
Quick check: Most ovens need about 10 to 15 minutes to reach 350°F. With the oven off and cool, look at the bake element for visible breaks. On a gas oven, check whether the igniter glows when you turn the oven on.
This is the most common cause. Ovens use special heat-rated appliance bulbs, and they do burn out.
A small switch in the door frame turns the light on when the door opens. If it fails, the light stays off.
On many newer ovens the control board runs the light. A failed relay keeps it off even with a good bulb.
Quick check: Turn off the power at the breaker and let the oven cool. Then remove the glass cover and replace the bulb with a heat-rated appliance bulb of the same wattage.
A weak igniter lets gas flow for longer before it lights. You may notice the smell and a soft whoosh when the burner finally catches.
A connection behind the range can loosen when the range is moved. A leak at the supply line itself is a job for your gas utility or a licensed plumber.
A valve that does not close fully can let a small amount of gas through even when the oven is off.
Safety first: A faint smell for a few seconds while a gas oven lights can be normal. If the smell is strong or does not go away, do not switch on lights or appliances, do not use the oven, leave the house and call 911 or your gas utility from outside.
Many oven error codes point to the temperature sensor. When its reading is out of range, the control stops the oven to be safe.
After a self-clean cycle, the lock motor or its switch can fail and leave the door locked with an error on the display.
A failing board or touchpad can show codes, beep on its own or react to buttons you did not press.
Quick check: Write down the code, then turn off the breaker for the oven for one minute and turn it back on. If the code returns, leave the oven off and tell us the code when you call.
When the oven quits, dinner plans change. A small local team makes it easier to get it working again.
Our 8 certified, insured technicians work around Leander every day. You speak with the team that does the repair, not an operator reading a script.
We test the igniter or elements, the sensor and the controls and explain the repair before any work starts. If you go ahead with the repair, the service call and diagnosis are free.
Every oven repair comes with a 3-month warranty on the work. We book visits seven days a week, 7am to 11pm.
We repair gas and electric ovens, wall ovens and ranges from these manufacturers. Have a different make? Call and tell us the model.
Brand names and logos belong to their owners. We are an independent repair company and are not affiliated with or authorized by these manufacturers.
Tell us the brand, whether the oven is gas or electric, and any error code on the display. We'll call you back to set up a visit in Leander or nearby.
Request a repair
Leave your details and we'll call you back to confirm the time of the oven repair visit.
Thank You!
Your message has been sent successfully. We'll get back to you shortly.
Your request is in. We'll call you shortly to set up the visit.
We come to your kitchen in Leander and the towns around it in Williamson and Travis counties.
Not sure if we reach your street? Give us a call and we'll tell you right away.
(111) 111-1111